Every Single CalculatorOne place for every calculator

Roof estimator

Enter the size of the house once and get the whole materials list for a shingle roof: shingles, underlayment, ice barrier, drip edge, ridge cap and nails.

Example: A homeowner calls for a re-roof quote on a 40 by 30 foot ranch. You measure the house from the ground, enter it here and have a full shingle order before you are back in the truck.

Your house

Measure the house at ground level, wall to wall. Width is the side with the triangle-shaped gable ends.

ft
ft
/12
Not sure? Use the roof pitch calculator.
in
How far the roof sticks out past the wall.
%
10 for gable, 15 for hip.
$
Optional. Adds a shingle cost.
Product sizes (change these to match what you are buying)
sq ft
ft
ft
ft
  • Roof area0
  • Squares to order0
  • Rafter length0
  • Eaves0
  • Rakes0
  • Ridge0

Materials list
ItemBuyHow it was worked out

What this estimator does

Most roofing calculators answer one question at a time. This one takes the size of the house once and works out everything a shingle roof needs, so you are not retyping the same measurements on six different pages.

Ridge Rake Eave Overhang Span (width) Run Rise Length
The run is half the span. Rakes are the sloped edges at the gable ends, and eaves are the level edges where gutters go.

How each quantity is worked out

Everything starts from the roof area. A sloped roof is larger than the floor under it, and the pitch multiplier says by how much.

Roof area = (length + 2 × overhang) × (width + 2 × overhang) × √(1 + (pitch ÷ 12)²)

That formula holds for both gable and hip roofs, as long as every side has the same pitch. What changes between the two is the edges. A gable roof has two eaves, four rakes and a ridge as long as the house. A hip roof has eaves all the way round, no rakes, a shorter ridge and four hips.

Hip length = run × √(2 + (pitch ÷ 12)²), where run is half the width plus the overhang

A worked example

A 40 by 30 foot house with a 12 inch overhang and a 6/12 gable roof covers 42 by 32 feet, which is 1,344 square feet on the flat. The multiplier for 6/12 is 1.118, so the roof is 1,503 square feet. With 10% waste you order 16.5 squares.

  • Shingles: 16.5 squares at 3 bundles each is 50 bundles.
  • Underlayment: 1,653 square feet at 400 per roll is 5 rolls.
  • Ice and water barrier: 84 feet of eave takes 2 rolls of 66 feet.
  • Drip edge: 84 feet of eave and 71.6 feet of rake, plus 10%, is 18 ten-foot pieces.
  • Ridge cap: the 42 foot ridge plus 10% is 2 bundles.
  • Nails: 320 per square comes to 5,290 nails, or 45 coils.

Switch the same house to a hip roof and the area stays at 1,503 square feet, but the eaves grow to 148 feet, the ridge shrinks to 10 feet and four 24 foot hips appear. That takes 4 bundles of cap in place of 2.

What is not on the list

  • Starter strip, step flashing, valley metal, pipe boots and vents. These depend on details the estimator cannot see.
  • Valleys and dormers. Add their area by raising the waste figure, or measure each section separately.
  • Labor and tear-off. The roofing cost calculator covers those.

Common questions

How accurate is this?

For a plain gable or hip roof it is the same arithmetic a supplier would do from your measurements. The more valleys, dormers and changes of pitch a roof has, the more you should treat it as a starting point and have the supplier or roofer confirm.

Can I send this to my roofer?

Yes. Use the copy link button under the list. The link opens this page with your numbers already filled in. The print button gives a clean one-page list for the supply counter.

Why does a hip roof need more waste?

Every shingle that meets a hip is cut at an angle, and the offcut is often too small to reuse. Fifteen percent is the usual allowance.

How we know this calculator is right

Every time the site is rebuilt, this calculator is run against answers worked out separately from its code. It is not published unless all of them match.

  • A 40 by 30 foot gable roof with 12 inch overhangs at 6/12: 1,503 square feet, 50 bundles, 84 feet of eaves and 42 feet of ridge.
  • The same house with a hip roof: 148 feet of eaves, 10 feet of ridge and four hips of 24 feet each.
  • A 30 by 30 foot pyramid roof at 12/12 is checked a second way, as four triangles, and must give the same area.
  • A hip roof turned a quarter turn, with length and width swapped, must give the same answers.
  • A flat roof must come out as the footprint and nothing more: 1,344 square feet for this house.
  • The estimator must agree with the single calculators on this site for the same roof.

What this proves: the calculator does the arithmetic of the formulas shown, correctly. What it cannot prove: your measurements, or figures such as waste and coverage, which are typical starting values you can change. Go by the product label and your local code.